Install
This page assumes Before you install is done.
Run every command in the hagistack/rocky10.2 directory.
6. Run preflight
Section titled “6. Run preflight”sudo ./hagistack all-in-one --check- What it does: checks the settings and the host, and prints every resolved setting and where it came from (command line, file, autodetected). It changes nothing.
- What it checks: OS and architecture, the management IP, that the provider NIC exists, the provider addresses (gateway and floating range inside the CIDR), the tenant CIDR, DNS, region,
virt_type, the RPM source, disk and memory. - Expected result: it ends without an error and prints the settings.
- What it does not check: whether the RPMs can be downloaded (checked in the RPM-source phase of the installation).
Without a configuration file, pass the settings as options:
sudo ./hagistack all-in-one --check \ --ext-nic eth1 --provider-cidr 198.51.100.0/24 --provider-gateway 198.51.100.1 \ --floating-start 198.51.100.100 --floating-end 198.51.100.2007. Install all-in-one
Section titled “7. Install all-in-one”sudo ./hagistack all-in-one- What it does: downloads and verifies the release RPMs from GitHub Releases and installs OpenStack 2026.1.
- Time: about 8 minutes on the verified all-in-one node (n2-standard-8), plus downloading the RPMs (about 108 MB).
- Expected result: it ends with
every phase completedand prints where the credentials are, the dashboard URL and the commands to add a compute node.
The phases run in this order:
- preflight
- RPM source (download; SHA-256, size, RPM-set identity and
rpm -Kchecks) - repositories
- SELinux
- secrets (passwords are generated)
- packages
- MariaDB → RabbitMQ → memcached
- Keystone → Glance → Placement → OVS/OVN → Neutron → Nova → nova-compute
- initial resources
- Horizon
Initial resources
Section titled “Initial resources”Each one is created only if a resource with that name does not exist.
| Resource | Details |
|---|---|
| Flavor | m1.tiny: 1 vCPU, 256 MiB RAM, 1 GiB disk |
| Image | cirros-0.6.3-x86_64, verified against its SHA-256 before upload, public |
| External network | hagistack-provider: flat, external, on physnet1. Its subnet hagistack-provider-subnet holds the floating range and has no DHCP |
| Tenant network | hagistack-tenant, with subnet hagistack-tenant-subnet |
| Router | hagistack-router: gateway on the provider network, interface on the tenant subnet |
| Security group | SSH (TCP 22) and ICMP rules on the admin project’s default group |
| Key pair | hagistack-key. The private key is /etc/hagistack/hagistack-key, mode 0600 |
8. Check the services with status
Section titled “8. Check the services with status”sudo ./hagistack status- What it does: shows the completed phases, the SELinux state and the state of every service unit.
- Expected result: every line under
servicessaysactive(MariaDB, RabbitMQ, memcached, httpd, Glance, OVN, Open vSwitch, the Neutron workers, Nova conductor, scheduler and compute, libvirtd).
9. Find the Horizon URL
Section titled “9. Find the Horizon URL”Horizon (the dashboard) runs on port 80 of the management IP:
http://MGMT_IP/dashboard/Example: http://192.0.2.10/dashboard/ (a documentation address).
The end of the installation output also shows it as Dashboard :.
10. Find the admin user and password
Section titled “10. Find the admin user and password”- User:
admin - Password:
OS_PASSWORDin/etc/hagistack/admin-openrc
sudo grep '^export OS_PASSWORD=' /etc/hagistack/admin-openrc11. Sign in to Horizon
Section titled “11. Sign in to Horizon”- Open
http://MGMT_IP/dashboard/in a browser. - Enter
adminand the password above, and Sign In. - Check that the project at the top left is
admin.
If you cannot sign in, see Troubleshooting.
To check the sign-in from the command line, use the bundled tests-horizon-login.sh:
sudo ./tests-horizon-login.shExit status 0 means PASS.
Next: Your first VM.